Work Day 16th December 2017

First the usual bits …..

LCP
The inside of the main LCP door was prepared for a repaint, see photo below. The door was rubbed down and lose paint removed before the priming of bare metal and a top coat can be applied.

LCP Door Prep for Painting wm.jpg

The main issue with the LCP door are its edges where a weatherproofed sealing strip filled the gap between the door and cabin frame. The residue of the long perished seal and glue took some effort to get back to bare metal ready for fitting new sealing strips.

Repair of an Argus 700 card – ME186 PeriBus Converter. The card in question developed a fault a month back when running the simulator and was removed from the Argus for fault finding. The ME186 was checked in the ‘workshop’ last week for any obvious fault, such checks look for overheated components and includes an ohms check between the +5V and 0V. For this particular card the power rail ohms check gave 10 ohms and not the 500 ohms of a serviceable ME186 The reason for carrying out this particular ohms check was down to recent experiences with resistive decoupling capacitors on some of the I/O cards. Next check was to touch the TTL devices on the card to feel is any were getting hot, with 10 ohms something probably was. The component found to be hot was not a TTL device but the precision 19.6608 MHz oscillator on the card. The photo shows the condition of the oscillator once removed.

ME186 Xtal 1 wm.jpg

This is not the first time we have experienced this fault on an ME186, it looks like the rubber pad on which the oscillator was mounted retains moisture or has a chemical constituent that causes corrosion. Note, three legs of the oscillator have corroded away. Oscillator replaced and the card was tested in the LCP yesterday and proved to be serviceable and now returned to our spares stock. If only all A700 card faults  were this straight forward!

T86 Radar
Dave and Ian spent the day working on fitting the final pieces for the new cabin floor. All plywood pieces have now been cut and positioned but some fettling is needed to get smooth joins between the plywood floor sections. The accompanying photo shows work in progress on fettling the plywood pieces to cover one of the wheel arches in the main cabin, Ian’s speciality.

T86 Fitting New Floor wm.jpg

Pete M also had a busy day but on the T86 roof, firstly rubbing down the filler used on all the new rivets before priming the roof, see accompanying photo of the freshly primed roof.

T86 Roof Primed wm.jpg

A large number of rivets had previously been replaced on the T86 roof as their heads had corroded away. The main cause for rivet corrosion being the mandrel hole, if not sealed, allows water ingress into the rivet and hence corrodes the barrel of the rivet completely away.

…. and now the other bits 

Saturday was our last working day of 2017 so it was time for a compulsory group photo of the workers on the day. From left to right, Pete Murray ex Ferranti engineer who commissioned many of the MK2A LCP’s. Pete Harry ex RAF T86 man, Dave Scobbie ex RAF LCP man and finally Ian Gibbon with no previous experience of Bloodhound but an important member of the team and an expert fettler.

Group Photo 1 wm.jpg

The whole team, including those who could not be there – Neil Cartman [fettler extraordinaire], Richard Vernon [historian] and Mike Strange [your scribe] , wish everyone a Happy Christmas and a Happy New Year.

Father Christmas on missile wm.jpg

After a winter break the team will be back in action on January 6th 2018, that’s assuming we have finished the beers courtesy of Ian who did us proud with a gift from a Stockport Brewer!

Group Photo 2 wm.jpg

 

Image result for holly

Advertisements

One thought on “Work Day 16th December 2017”

  1. A Happy Christmas to you all and the great job you have done on the Lcp and T86 this year, you deserve a warm Saturday with some of your beer.

    I wish I could send some significant information on the progress with Bloodhound in the Aero Collection I suppose that getting it in front of the public is some thing, but very few people know what it is, and the expensive video and information boards are useless. I go in occassionaly and give a bit of a conducted tour of the GW bits, to persons who look interested and can find the GW bits behind the ” Secret Wall “

    Like

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s